97Ti, 95Ti, 93T Treadmills
Assembly Instructions
IMPORTANT SAFETY INSTRUCTIONS !
ꢀ DO NOT position the rear of the treadmill within 6 feet ( 2 meters ) of the nearest obstruction. The
sides of the treadmill should maintain a minimum clearance of 8 inches ( 20 cm ) from the nearest
treadmill or other obstruction.
ꢀ DO NOT locate the treadmill outdoors, near swimming pools, or in areas of high humidity.
ꢀ DO verify the contents of the delivery carton against the accompanying parts listing prior to setting
the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer
Support Services at the number listed on the back page of this assembly instruction booklet.
ꢀ Save the shipping cartons in case of return.
ꢀ DO read the entire Operation Manual prior to attempting to operate this machine, as this is essential
for proper use. The Manual explains how to properly use the treadmill and helps you to train your
staff effectively.
ꢀ NE placez PAS l’arrière du tapis roulant dans un rayon de 2 m (6 pi) de l’obstruction la plus proche.
Les côtés de l’appareil ne doivent pas se trouver à moins de 20 cm (8 po) du tapis roulant voisin ou
de toute autre obstruction.
ꢀ NE placez PAS le tapis roulant à l’extérieur, près d’une piscine ou dans des endroits très humides.
ꢀ VÉRIFIEZ si l’emballage contient toutes les pièces de la liste jointe avant de le mettre de côté. Si
des pièces sont absentes, contactez l’assistance clientèle de Life Fitness au numéro indiqué au dos
de cette brochure d’instruction de montage..
ꢀ VÉRIFIEZ si l’emballage contient toutes les pièces de la liste jointe avant de le mettre de côté. Si
des pièces sont absentes, contactez l’assistance clientèle de Life Fitness au numéro indiqué au dos
de cette brochure d’instruction de montage.
TOOLS REQUIRED FOR ASSEMBLY...
Phillips screwdriver, Torx wrench, 3/4” combination wrench, flat blade screwdriver (or 5/16” nut driver)
PARTS DESCRIPTION
1
3
5
7
9
LEFT UPRIGHT
Qty: 1
Qty: 2
Qty: 1
Qty: 1
Qty: 1
2
RIGHT UPRIGHT
Qty: 1
HANDLEBAR (LEFT AND RIGHT)
LEFT INSIDE HANDLEBAR SHROUD
LEFT OUTSIDE HANDLEBAR SHROUD
DISPLAY CONSOLE
4
™
ERGO FRONT CROSSBAR
Qty: 1
6
RIGHT INSIDE HANDLEBAR SHROUD
RIGHT OUTSIDE HANDLEBAR SHROUD
Qty: 1
8
Qty: 1
10
LOWER UPRIGHT COVER (LEFT AND RIGHT)
0017-00101-1265
Qty: 2
11
13
15
LEFT ACCESSORY TRAY
HANDLEBAR CAP
Qty: 1
Qty: 2
Qty: 6
12
14
16
RIGHT ACCESSORY TRAY
Qty: 1
Qty: 2
Qty: 6
REAR FRAME ENDCAP
HANDLEBAR SHROUD SCREW
0017-00101-1770
ENDCAP / UPRIGHT COVER SCREW
0017-00101-1772
17
19
21
23
25
27
DISPLAY CONSOLE / HANDLEBAR SUPPORT SCREW Qty: 6
0017-00101-1773
18
20
22
24
26
SCREW GROMMET
0017-00042-0326
UPRIGHT MOUNTING BOLT
0017-00101-1778
FRONT CROSSBAR NUT
0017-00103-0327
UPRIGHT WASHER
0017-00104-0335
FRONT CROSSBAR GROMMET
(Models 95Ti & 97Ti Only)
Qty: 2
Qty: 4
Qty: 4
Qty: 4
Qty: 2
FRONT CROSSBAR SCREW
0017-00101-1774
ACCESSORY TRAY SCREW
0017-00101-1780
LINECORD CLIP
0017-00042-0838
Qty: 4
Qty: 8
Qty: 5
Qty: 2
Qty: 2
UPRIGHT PLUG
HANDLEBAR GROMMET
(Model 93T Only)
15
18
16
17
19
20
21
22
23
24
1”
2”
3”
4”
5”
IMPORTANT!
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS
NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
IMPORTANT!
NE JETEZ PAS LE KIT D’EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS LES
ÉLÉMENTS NÉCESSAIRES POUR L’INSTALLATION.
1. Remove the four SCREWS (A) securing the FRONT GRILL (B) to the
E
FRAME (C). Remove the FRONT GRILL and set it aside.
D
2. Remove the four SCREWS (D) securing the MOTOR COVER (E). Lift and
remove the MOTOR COVER and set it aside.
3. Locate the LEFT UPRIGHT (#1). Lay the LEFT UPRIGHT across the belt
and deck with the notched end near the LEFT UPRIGHT MOUNTING
BRACKET (F).
B
4. Unwrap the MAIN WIRE HARNESS (G) leading from the LEFT UPRIGHT
MOUNTING BRACKET (F). Feed the MAIN WIRE HARNESS through the
LEFT UPRIGHT (#1). Carefully tilt the LEFT UPRIGHT upwards and position
the notched end of the LEFT UPRIGHT over the LEFT UPRIGHT
MOUNTING BRACKET. With the LEFT TOP MOUNTING PLATE (H)
directed forward, slide the LEFT UPRIGHT down over the LEFT UPRIGHT
MOUNTING BRACKET and pre-installed BOLT and WASHER until it rests
on the FRAME (C). Secure the LEFT UPRIGHT to the LEFT UPRIGHT
MOUNTING BRACKET using two BOLTS (#20) and WASHERS (#24). One
BOLT and WASHER on the inside of the LEFT UPRIGHT and one BOLT
and WASHER on the front side of the LEFT UPRIGHT. Leave the BOLTS
loose at this time.
C
A
J
G
NOTE: BE CAREFUL NOT TO DAMAGE THE MAIN WIRE HARNESS (G)
WHEN ROUTING IT THROUGH THE LEFT UPRIGHT (#1) OR WHEN
SLIDING THE LEFT UPRIGHT OVER THE LEFT UPRIGHT MOUNTING
BRACKET (F).
H
NOTE: BE SURE THE PRE-INSTALLED WASHER IS ON THE OUTSIDE
OF THE LEFT UPRIGHT (#1) WHEN SLIDING IT DOWN TO REST ON
THE FRAME (C).
2
5. Locate the RIGHT UPRIGHT (#2). With the RIGHT TOP MOUNTING
PLATE (J) directed forward, slide the RIGHT UPRIGHT down over the
RIGHT UPRIGHT MOUNTING BRACKET (K) and pre-installed BOLT and
WASHER until it rests on the FRAME (C). Secure the RIGHT UPRIGHT to
the RIGHT UPRIGHT MOUNTING BRACKET using two BOLTS (#20) and
WASHERS (#24). One BOLT and WASHER on the inside of the RIGHT
UPRIGHT and one BOLT and WASHER on the front side of the RIGHT
UPRIGHT. Leave the BOLTS loose at this time.
1
20 24
20 24
NOTE: BE SURE THE PRE-INSTALLED WASHER IS ON THE OUTSIDE
OF THE RIGHT UPRIGHT (#2) WHEN SLIDING IT DOWN TO REST ON
THE FRAME (C).
K
20
24
C
6. (Model 93T Only) Locate both HANDLEBARS (#3). Slide one
HANDLEBAR GROMMET (#27) over each HANDLEBAR. The groove of
the HANDLEBAR GROMMET should face outward.
C
24
F
7. With the bend of one HANDLEBAR (#3) directed to the outside of the
treadmill, insert the HANDLEBAR into the RIGHT UPRIGHT HANDLEBAR
BRACKET (L) as shown. Be sure the HANDLEBAR MOUNTING HOLES
are aligned. Repeat for the left side HANDLEBAR.
M
6
26
5
™
8. Locate the ERGO FRONT CROSSBAR (#4) and position the ERGO
26
FRONT CROSSBAR with the plastic SMART STOP COVER (M) facing
upward and forward as shown. Locate and slide the left and right INSIDE
HANDLEBAR SHROUDS (#5 & #6) over the corresponding ends of the
ERGO FRONT CROSSBAR as shown. Slide the left and right INSIDE
HANDLEBAR SHROUDS towards the center of the ERGO FRONT
CROSSBAR as shown.
19
L
22
4
O
P
NOTE: BE CAREFUL NOT TO DAMAGE THE ANY WIRE HARNESSES
THAT MAY BE LEADING FROM THE ENDS OF THE ERGO FRONT
CROSSBAR (#4).
N
3
22
2
17
9. Install one FRONT CROSSBAR GROMMET (#26), rounded end first, over
either end of the ERGO FRONT CROSSBAR (#4). Position the grommets
just over the end brackets to meet the overmolding.
3
1
17
NOTE: BE CAREFUL NOT TO DAMAGE THE ANY WIRE HARNESSES
THAT MAY BE LEADING FROM THE ENDS OF THE ERGO FRONT
CROSSBAR (#4).
M
6
26
10. Position the right end of the ERGO FRONT CROSSBAR (#4) near the
large access hole on the inside of the RIGHT UPRIGHT HANDLEBAR
BRACKET (L).
5
26
Align the ERGO FRONT CROSSBAR MOUNTING HOLES with those in
the RIGHT UPRIGHT HANDLEBAR BRACKET and secure using two
BOLTS (#19), from the inside of the treadmill, and NUTS (#22). Tighten
the BOLTS securely. Insert one SCREW (#16) from under the RIGHT
UPRIGHT HANDLEBAR BRACKET. Tighten the SCREW securely.
19
L
22
4
O
P
11. Position the left end of the ERGO FRONT CROSSBAR (#4) near the
large access hole on the inside of the LEFT UPRIGHT HANDLEBAR
BRACKET (N).
N
3
22
2
17
(Models 97Ti and 95Ti Only) Feed the SMART STOP CABLE (O) and
HEART RATE CABLE (P) into the access hole downward out the bottom
of the LEFT UPRIGHT HANDLEBAR BRACKET.
3
1
17
Align the crossbar mounting holes with those in the LEFT UPRIGHT
HANDLEBAR BRACKET and secure using two BOLTS (#19), from the
inside of the treadmill, and NUTS (#22). Tighten the BOLTS securely.
Insert one SCREW (#16) from under the LEFT UPRIGHT HANDLEBAR
BRACKET. Tighten the SCREW securely.
NOTE: BE CAREFUL NOT TO PINCH THE SMART STOP CABLE (O)
AND HEART RATE CABLE (P) (IF EQUIPPED) WHEN ASSEMBLING
THE ERGO FRONT CROSSBAR (#4) TO THE LEFT UPRIGHT
HANDLEBAR BRACKET.
(Models 97Ti and 95Ti Only) Feed the SMART STOP CABLE (O) and
HEART RATE CABLE (P) upward through the top of the LEFT UPRIGHT
(#1).
12. Slide the LEFT INSIDE HANDLEBAR SHROUD (#5) near the LEFT
UPRIGHT HANDLEBAR BRACKET (N).
(Model 93T Only) Position the HANDLEBAR GROMMET (#27) at the end
of the LEFT INSIDE HANDLEBAR SHROUD. Install the HANDLEBAR
GROMMET onto the inside edge of the LEFT INSIDE HANDLEBAR
SHROUD as shown.
Locate and position the LEFT OUTSIDE HANDLEBAR SHROUD (#7) to
match the LEFT INSIDE HANDLEBAR SHROUD.
(Model 93T Only) Install the remaining portion of the HANDLEBAR
GROMMET onto the LEFT OUTSIDE HANDLEBAR SHROUD as it is
positioned to match the LEFT INSIDE HANDLEBAR SHROUD.
9
S
R
Secure the SHROUDS together using three SCREWS (#15). Tighten the
SCREWS securely. Do not overtighten the SCREWS. Repeat the
procedure for the RIGHT INSIDE and OUTSIDE HANDLEBAR SHROUDS
(#6 and #8).
J
13. Locate the DISPLAY CONSOLE (#9). Remove the eight SCREWS (Q) from
the back of the DISPLAY CONSOLE and separate the front of the DISPLAY
CONSOLE from the rear. Position the REAR CONSOLE (R) over the LEFT
and RIGHT TOP MOUNTING PLATES (H & J) as shown. From the bottom
of the LEFT and RIGHT TOP MOUNTING PLATES, secure the REAR
CONSOLE using four screws (#17). Tighten the SCREWS securely. Do not
overtighten the SCREWS.
H
Q
5
8
17
N
14. Position and rest the FRONT CONSOLE (S) facedown across the
HANDLEBARS (#3). Connect all CONNECTORS leading from the LEFT (if
equipped) and RIGHT UPRIGHTS (#1 & #2) to the corresponding
CONNECTORS located on the FRONT CONSOLE. Feed any excess WIRE
HARNESS into the UPRIGHTS. Carefully route all WIRE HARNESSES
through the WIRE HARNESS GUIDES (T) located at the lower left of the
REAR CONSOLE (R)
7
6
15
3
3
2
15. Tilt the FRONT CONSOLE (S) upright and in position over the REAR
CONSOLE (R). Secure the FRONT CONSOLE to the REAR using the
previously removed eight SCREWS (Q). Tighten the SCREWS securely. Do
not overtighten the SCREWS.
T
1
NOTE: BE CAREFUL NOT TO PINCH THE ANY CABLES WHEN
ASSEMBLING THE FRONT CONSOLE (S) TO THE REAR CONSOLE (R).
R
1
16. Locate the LEFT ACCESSORY TRAY (#11). Carefully slide the tray into the
top of the LEFT UPRIGHT (#1) as shown until fully seated. Secure the
accessory tray to the LEFT TOP MOUNTING PLATE (H) using four screws
(#21). Repeat the procedure for the RIGHT ACCESSORY TRAY (#12) and
RIGHT TOP MOUNTING PLATE (J).
11
12
17. Tighten all UPRIGHT BOLTS securely.
18. Replace the MOTOR COVER (E) and secure the MOTOR COVER to the
FRAME (C) using the four previously removed SCREWS (D). Tighten the
SCREWS securely. Do not overtighten the SCREWS.
21
19. Replace the FRONT GRILL (B) and secure the FRONT GRILL to the
FRAME (C) using the four previously removed SCREWS (A). Tighten the
SCREWS securely. Do not overtighten the SCREWS.
2
1
20. Locate one SCREW GROMMET (#18). Insert the SCREW GROMMET into
the square hole located above the top inside mounting bolt of the RIGHT
UPRIGHT (#2). Repeat for the remaining SCREW GROMMET and LEFT
UPRIGHT (#1)
21. Locate one LOWER UPRIGHT COVER (#10). Position the LOWER
UPRIGHT COVER at the bottom notch of the RIGHT UPRIGHT (#2) making
sure the top lip of the UPRIGHT COVER is engaged under the outside notch
of the RIGHT UPRIGHT. Secure the UPRIGHT COVER to the RIGHT
UPRIGHT using one SCREW (#16). Tighten the SCREW securely. Do not
overtighten the SCREW. Repeat the procedure for the LEFT UPRIGHT (#1)
and remaining UPRIGHT COVER.
2
16
10 18
22. Locate the UPRIGHT PLUGS (#25). Insert one UPRIGHT PLUG into each of
the two access holes located on the lower outside of the LEFT and RIGHT
UPRIGHTS (#1 & #2).
23. Locate and press the HANDLEBAR CAPS (#13) over the ends of the
HANDLEBARS (#3). Be sure the HANDLEBAR CAPS are fully seated.
24. Using two SCREWS (#16) each, attach the two REAR FRAME END CAPS
(#14) to the FRAME (C) as shown. Tighten the SCREWS securely. Do not
overtighten the SCREWS.
25. Refer to the Operation Manual for power requirements, proper line cord
routing, and other critical product information before connecting the treadmill
to a power source.
3
13
14
C
16
14
PRE-OPERATION CHECKLIST
⇒ Ensure that all fasteners are tight.
⇒ Make sure the STRIDING BELT is properly tensioned and aligned according to the Operation Manual.
⇒ Check the operation of the STOP switch and tether switch assembly.
(See Operation Manual.)
⇒ Confirm the display console is set to English or Metric units.
(See Optional Settings ENG/MET in Operation Manual.)
⇒ Refer to the Operation Manual for real time clock setting.
⇒ Read the entire Operation Manual before using the treadmill.
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE
⇒ Vérifiez si tous les dispositifs de fixation sont serrés.
⇒ Assurez-vous que le TAPIS est bien tendu et aligné, conformément aux instructions du manuel
d’utilisation.
⇒ Vérifiez le fonctionnement de l'interrupteur d'ARRÊT et reliez-le
(cf. Manuel de l'utilisateur).
⇒ Vérifiez si la console d’affichage est sur le système métrique ou anglais.
(Référez-vous aux réglages facultatifs relatifs aux systèmes de mesure dans le Manuel de
l’utilisateur.)
⇒ Consultez le Manuel de l’utilisateur pour le réglage de l’horloge en temps réel.
⇒ Lisez le Manuel de l’utilisateur dans son intégralité avant d’utiliser le tapis roulant.
Before attempting to operate your Treadmill, it is imperative that you familiarize yourself with the contents of the
Operation Manual. If your Life Fitness treadmill does not respond as described in the OPERATION MANUAL contact
the nearest Life Fitness Service Center as listed in the OPERATION MANUAL.
Life Fitness Customer Support Services
(800) 351-3737 or (847) 451-0036
Prior to your call, please be sure you have located and noted the
MODEL NUMBER & SERIAL NUMBER.
The Model & Serial number information of your Life Fitness Treadmill is contained in a label
located on the front of the unit.
©2004 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness, Lifepulse, FlexDeck and Smart Stop are
trademarks of Brunswick Corporation.
Polar is a registered trademark of Polar Electro, Inc.
MO51-00K58-A181
09.04
|